Audi 100/A6

1990-1997 of release

Repair and car operation



Audi 100/A6
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 3.2. Diesel engines
+ 3.3. Removal and partition of engines
+ 4. Cooling system
+ 5. Heating and ventilation
- 6. Fuel system
   + 6.1.2. Technical characteristics
   - 6.2. Multipoint system of injection of fuel
      6.2.2. Technical characteristics
      6.2.3. Air filter
      6.2.4. Accelerator rope
      6.2.5. Elements of system of injection of Motronic/Jetronic fuel
      6.2.6. Elements of system of injection of Digifant fuel
      6.2.7. Fuel filter
      6.2.8. Fuel pump and fuel level sensor
      6.2.9. Fuel tank
      6.2.10. Pressure release from system of injection of fuel
      6.2.11. Inlet collector
      6.2.12. Check of system of injection of fuel
      6.2.13. Unleaded gasoline
   + 6.3. System of injection of MPI/MPFI (6-cylinder engines)
   + 6.4. Power supply system of diesel engines
   6.5. Device of service of heating
   6.6. Diagnostics of malfunctions of system of heating
   6.7. Conditioner: not only "pluses", but also "minuses"
   6.8. Rules of service of the conditioner
+ 7. Exhaust system
+ 8. Systems of start, ignition
+ 9. Transmission
+ 10. Brake system
+ 11. Suspension brackets, steering
+ 12. Body
+ 13. Electric equipment
+ 14. Good advice


ff85f19c

6.2.5. Elements of system of injection of Motronic/Jetronic fuel

GENERAL INFORMATION

SENSOR OF THE STREAM OF AIR (MOTRONIC 3.2)

Arrangement of the sensor of a stream of air (ADR engine)

On the ADR engine the sensor of a stream of air is established on the top cover of the air filter.

Removal

PERFORMANCE ORDER
1. Uncover.
2. Disconnect an air branch pipe from the sensor (ADR engine).
3. Disconnect the socket of connection of the sensor (ADR engine).
4. Turn off fixing screws and remove the sensor.

Installation

Installation is carried out upside-down removals.

SENSOR OF THE STREAM OF AIR (KE MOTRONIC/JETRONIC)


Elements of the sensor of a stream of air on the ACE engine

1. Fixing screw
2. Bolt of connection of a banjo
3. Fuel distributor
4. Bolt of connection of a banjo
5. Sealing rings
6. Tube of supply of fuel
7. Fixing screw
8. Pressure regulator
9. Bolt of connection of a banjo
10. Sensor of a stream of air
11. Cap
12. Sealing ring
13. Lock screw
14. Sealing ring
15. Plunzher
16. Fixing arm
17. Blowing-off valve
18. Fastening
19. Fixing arm
20. Screw
21. Ventilating hose
22. Fixing arm
23. Diafragmenny regulator of pressure
24. Return топливопровод

Removal


PERFORMANCE ORDER
1. Mark fuel tubes and disconnect them from the fuel distributor.
2. Remove an airintaking branch pipe.
3. Turn off fixing bolts and remove the sensor.

Installation

Installation is carried out upside-down removals.

POTENTIOMETER OF THE BUTTERFLY VALVE (MOTRONIC 3.2) OR SENSOR OF PROVISION OF THE BUTTERFLY VALVE (KE MOTRONIC/JETRONIC)

Removal

PERFORMANCE ORDER
1. Disconnect the connection socket.
2. Turn off fixing screws and remove a potentiometer or the sensor.

Installation

Installation is carried out upside-down removals.

THE AIR TEMPERATURE SENSOR IN THE INLET COLLECTOR (MOTRONIC 3.2)

Removal

PERFORMANCE ORDER
1. Disconnect the connection socket.
2. Turn off fixing bolts and remove
sensor.

Installation

Installation is carried out upside-down removals.

MODULE OF POSITIONING OF THE BUTTERFLY VALVE (MOTRONIC 3.2)

Removal and installation of the module are carried out similar to a butterfly valve potentiometer.

SENSOR OF SPEED OF MOVEMENT OF THE CAR (MOTRONIC 3.2)

The sensor is established in the speedometer block, and for its replacement it is necessary to replace a speedometer.

THE SENSOR OF TEMPERATURE OF COOLING LIQUID (ALL SYSTEMS)

Removal

PERFORMANCE ORDER
1. Merge approximately the one fourth part of cooling liquid from the engine.
2. Disconnect the socket of connection of the corresponding sensor and unscrew it from a nest.

Installation

Installation is carried out upside-down removals.

SENSOR OF SPEED OF OPERATION OF THE ENGINE (ALL SYSTEMS)

Removal

PERFORMANCE ORDER
1. Disconnect the socket of connection of the sensor.
2. Turn off a fixing bolt and remove the sensor.

Installation

Installation is carried out upside-down removals.

BUTTERFLY VALVE CASE (ALL SYSTEMS)

Removal

PERFORMANCE ORDER
1. Disconnect an accelerator rope.
2. Disconnect connection sockets, vacuum and air hoses.
3. Turn off fixing bolts and remove the butterfly valve case.

Installation

Installation is carried out upside-down removals.

INJECTORS AND FUEL COLLECTOR (MOTRONIC 3.2)

Removal

PERFORMANCE ORDER
1. Disconnect a vacuum hose, fuel tubes and hoses from the fuel
collector.
2. Disconnect sockets of connection of injectors and the Hall sensor.
3. Turn off fixing bolts and remove a fuel collector.

Installation

Installation is carried out upside-down removals.

REGULATOR OF PRESSURE OF FUEL (MOTRONIC 3.2)

Removal

PERFORMANCE ORDER
1. Disconnect a vacuum hose from a regulator.
2. Remove a fixing clip and remove a regulator from a fuel collector.

Installation

Installation is carried out upside-down removals.

SENSOR OF THE HALL (MOTRONIC 3.2)

Removal

PERFORMANCE ORDER
1. Disconnect the socket of connection of the sensor.
2. Turn off fixing bolts and remove the sensor.

Installation

Installation is carried out upside-down removals.

OXYGEN SENSOR (ALL SYSTEMS)

Arrangement of the oxygen sensor (ADR engine)


Removal

PERFORMANCE ORDER
Disconnect the socket of connection of the sensor and unscrew the sensor from a final collector.

Installation

Installation is carried out upside-down removals.

ELECTRONIC CONTROL UNIT

Removal

PERFORMANCE ORDER
1. Remove furnish panels.
2. Turn off fixing screws and remove casings of the electronic control unit.
3. Turn off fixing screws and remove the electronic control unit, having disconnected the connection socket.

Installation

Installation is carried out upside-down removals.

FUEL INJECTORS (КЕ)

Removal

PERFORMANCE ORDER
1. Disconnect sockets of connection of injectors.
2. Remove cooling branch pipe if it is necessary.
3. Remove a fuel collector (if it is necessary), turn off nuts of connections and disconnect fuel tubes.
4. Remove injectors.

Installation

Installation is carried out upside-down removals.