Audi 100/A6

1990-1997 of release

Repair and car operation



Audi 100/A6
+ 1. Maintenance instruction
- 2. Maintenance
   + 2.1.2. Regular maintenance
   + 2.2. Models with diesel engines
+ 3. Engines
+ 3.2. Diesel engines
+ 3.3. Removal and partition of engines
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. Exhaust system
+ 8. Systems of start, ignition
+ 9. Transmission
+ 10. Brake system
+ 11. Suspension brackets, steering
+ 12. Body
+ 13. Electric equipment
+ 14. Good advice


ff85f19c
Читаем тут: https://snovonovo.ru

2. Maintenance

2.1. Models with petrol engines

2.1.1. Introduction

GENERAL INFORMATION

Impellent compartment of models with the petrol 20-klapanny engine in volume of 1,8 l

1. Cover of a jellied mouth of oil
2. Air filter
3. Fuel filter
4. Vrkhney fastening of a rack of a forward suspension bracket
5. Tank of brake liquid
6. Sensor of a stream of air
7. Inlet collector
8. Shchup for check of level of oil

9. Broad block of system of cooling
10. Tank of system of the hydraulic booster of a steering
11. A tank of washing liquid
12. generator
13. A directing roller
14. ABS module

The bottom view of an impellent compartment of models with the petrol 20-klapanny engine in volume of 1,8 l

1. Reception pipe of an exhaust system
2. Bottom lever of a forward suspension bracket
3. Stabilizer of cross-section stability of a forward suspension bracket
4. Brake support
5. Horns of a sound signal
6. Lever of fastening of the engine
7. Cap of a drain opening of the oil pallet

Bottom view of a back part of a body

1. Intermediate exhaust silencer
2. Longitudinal lever of a back suspension bracket
3. Rope of the hand brake
4. Rack of a back suspension bracket and spring
5. Back axis
6. Cross-section draft


This section is intended to help the motorist to support the car in good repair, to reduce fuel consumption and oils and to prolong car service life.

The general plan of maintenance of the car is provided in the section with detailed transfer of operations of maintenance.

Carrying out maintenance according to the provided plan of maintenance will provide long and reliable service of the car. This plan of maintenance is full therefore it is recommended to perform all operations of maintenance at the appointed time.

At car service you will notice that some operations can be combined with carrying out other operations is follows from essence of operations of maintenance. For example, if you lifted the car for carrying out any operation, elements of system of production of the fulfilled gases can be checked at the same time with check of elements of a suspension bracket or a steering.

Before the beginning of work it is necessary to be prepared for carrying out maintenance. Read all description of operation which you are going to execute, and get necessary tools and spare parts. If you faced a serious problem, address to experts.

 
Volumes
Models with the 4-cylinder engine Models with the 5-cylinder engine Models with the 6-cylinder engine
Engine oil (including the filter)
3,0 l
4,5 l
5,0/5,5 l
Cooling system
7,0 l
8,0 l
9,0 l

Transmission:
  – mechanical transmission
2,4 l
  – automatic transmission:
     • total amount
5,5 l
     • liquid replacement
3,5 l
     • main transfer of an automatic transmission
1,0 l
System of the hydraulic booster of a steering:
  – models with automatically adjustable back suspension bracket
2,5 l
  – models with a usual back suspension bracket
1,1 l
Fuel tank:
  – all models (approximately)
80 l
Engine:
  – oil filter:
     • models with the engine ADR, ABK, AAE, AAD, AAR coding
Champion C160
     • models with the EXPERT engine coding
Champion C149
     • models with the AAN, ABC, ACK engine coding
Champion
     • models with the AAN engine coding
Champion
Cooling system:
  – content of antifreeze:
     • 40 % content of antifreeze
Protection to–25 ° With
     • 50 % content of antifreeze
Protection to–35 ° With
Power supply system:
  – air filter
Champion U572
  – fuel filter
Fuel filter
Ignition system:
  – corner of an advancing of ignition:
     • ADR engine
It is supervised by a control system of operation of the engine
     • AAE engines, EXPERT, AVK and AAD
6 °±1 ° to VMT
     • AAR engine
15 °±1 ° to VMT
     • engine AAN, AAH, ACK
It is supervised by a control system of operation of the engine
     • ABC engine
7 °–27 ° to VMT
Spark plugs:
  – models with the engine ADR, ABK, AAD, AAR coding
Champion N7BYC
  – models with the EXPERT engine coding
Champion C6BYC
  – models with the AAE engine coding
NGK BUR6ET
  – models with the AAN engine coding
Bosch F5DPOR
  – models with the engine ABC, AAH, ACK coding
NGK BKUR6ET-10
Spark gap of spark plugs:
All models
0,8 mm
Brake system:
  – minimum admissible thickness of a frictional material of brake overlays of forward brakes
2,0 mm
  – minimum admissible thickness of brake overlays of back brakes
7 mm
  – minimum admissible thickness of a frictional material of brake shoes of back brakes
2,5 mm
Driving belt:
  – deviation:
     • new driving belt of the generator
2,0 mm
     • driving belt of the generator which was in operation
5,0 mm
     • driving belt of the pump of system of the hydraulic booster of a steering
10,0 mm
     • driving belt of the compressor of the conditioner
5,0 mm

Moments of an inhaling, N of m.
Fixing bolt of the generator
35
Fastening of a natyazhitel of the generator
20
Nut of fastening of a natyazhitel of the generator
35
Nut of fastening of a jellied tube of an automatic transmission (097)
80
Cap of a jellied opening / opening for check of level of liquid of an automatic transmission
25
Cap of a viewing opening of an automatic transmission (01N)
15
Perepuskny tube of an automatic transmission (01N)
2
Cap of a jellied opening / opening for check of level of oil of a mechanical transmission:
  – transmission 012
25
  – transmission 01Е
40
Fastening of the pump of system of the hydraulic booster of a steering
25
Bolts of fastening of wheels
110
Spark plugs:
  – models with the engine ADR, AAE, ABK coding
30
  – models with the EXPERT, AAD, AAR engine coding
20
  – models with the AAN engine coding
20
  – models with the engine ABC, AAH, ACK coding
30
Cap of a drain opening of the oil pallet
30