Audi 100/A6

1990-1997 of release

Repair and car operation



Audi 100/A6
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
- 3.2. Diesel engines
   + 3.2.1.2. Technical characteristics
   - 3.2.2. 5-cylinder engines
      3.2.2.2. Technical characteristics
      3.2.2.3. Sinkhronizatsionnye of a gazoraspredeleniye label
      3.2.2.4. Compression check
      3.2.2.5. Gas-distributing belt
      3.2.2.6. Driving belt of the fuel pump
      3.2.2.7. Natyazhitel of a gas-distributing belt and asterisk
      3.2.2.8. Additional driving belt
      3.2.2.9. Camshaft cover
      3.2.2.10. Camshaft epiploons
      3.2.2.11. Epiploons of a cranked shaft
      3.2.2.12. Head of cylinders
      3.2.2.13. Hydraulic pushers
      3.2.2.14. Flywheel
      3.2.2.15. Engine fastenings
      3.2.2.16. Oil pallet
      3.2.2.17. Oil pump and maslozaborny branch pipe
+ 3.3. Removal and partition of engines
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. Exhaust system
+ 8. Systems of start, ignition
+ 9. Transmission
+ 10. Brake system
+ 11. Suspension brackets, steering
+ 12. Body
+ 13. Electric equipment
+ 14. Good advice


ff85f19c

3.2.2.5. Gas-distributing belt

Removal

PERFORMANCE ORDER
1. Disconnect a wire of the minus plug of the accumulator.
2. Lift and fix a forward part of the car.
3. Remove a front bumper.
4. Unscrew screws of forward headlights and remove both lobbies of a headlight.
5. Disconnect a rope from the lock of a cowl and remove a cross-piece. Remove a small air inlet from the top part of a radiator.
6. Braid the bottom nut of a radiator.
7. Shift a radiator aside and fix it.
8. Turn a natyazhitel of a belt clockwise.
9. Remove an additional driving belt.
10. Remove the fan.
11. Stop a pulley and weaken a nut.
12. Remove the fan block.
13. Remove the top cover of a driving belt.
14. Unscrew bolts of a natyazhitel.
15. Unscrew bolts of a spring of a natyazhitel.
16. Remove a natyazhitel.
17. Uncover a camshaft.
18. Remove a forward top cover of a gas-distributing belt.
19. Remove the bottom cover of a gas-distributing belt.
20. Establish the N1 piston in VMT, having combined sinkhronizatsionny labels on a back part of a pulley of a cranked shaft and an internal cover of a gas-distributing belt.
21. Stop a flywheel.
22. Weaken the central bolt of the shock-absorber.
23. Get a bolt.
24. Unscrew the bolts, fixing the shock-absorber to an asterisk of a cranked shaft.
25. Remove the shock-absorber.
26. Remove a gas-distributing belt.

Check

Examine a belt on existence of pollution by greasing or oil, and also on existence of wear or damages. If necessary replace a belt.

Installation

PERFORMANCE ORDER
1. Put on a belt an asterisk of a cranked shaft.
2. Put on a belt a camshaft asterisk.
3. In models let out to 1995 g turn a natyazhitel counter-clockwise to pull a belt. Adjust a belt tension, it should be overwound no more than on 90 °. Tighten a bolt of a natyazhitel.
4. In later models to pull a belt turn a natyazhitel clockwise while labels on a natyazhitel will not be combined. Tighten bolts of a natyazhitel.
5. Tighten a bolt of an asterisk of a camshaft.
6. Establish the shock-absorber.
7. Insert the central bolt of the shock-absorber
8. Tighten a shock-absorber bolt.
9. Establish the bottom cover of a gas-distributing belt.
10. Insert bolts.
11. Establish the top cover of a gas-distributing belt.
12. Latch clips.