Audi 100/A6

1990-1997 of release

Repair and car operation



Audi 100/A6
+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Engines
   + 3.1.1.2. Technical characteristics
   - 3.1.2. 5-cylinder engines
      3.1.2.2. Technical characteristics
      3.1.2.3. Sinkhronizatsionnye of a gazoraspredeleniye label
      3.1.2.4. Compression check
      3.1.2.5. Gas-distributing belt
      3.1.2.6. Natyazhitel of a gas-distributing belt, asterisk
      3.1.2.7. Additional driving belt
      3.1.2.8. Camshaft cover
      3.1.2.9. Camshaft epiploon
      3.1.2.10. Epiploons of a cranked shaft
      3.1.2.11. Head of cylinders
      3.1.2.12. Hydraulic pushers
      3.1.2.13. Flywheel
      3.1.2.14. Engine fastenings
      3.1.2.15. Oil pallet
      3.1.2.16. Oil pump and maslozaborny branch pipe
   + 3.1.3. 6-cylinder engines
+ 3.2. Diesel engines
+ 3.3. Removal and partition of engines
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. Exhaust system
+ 8. Systems of start, ignition
+ 9. Transmission
+ 10. Brake system
+ 11. Suspension brackets, steering
+ 12. Body
+ 13. Electric equipment
+ 14. Good advice


ff85f19c

3.1.2.5. Gas-distributing belt

Removal

Gas-distributing belt

1. Spring clip
2. Top cover of a belt
3. Gas-distributing belt
4. Bolt of an asterisk of a camshaft
5. Camshaft asterisk
6. Natyazhitel
7. Back cover of a distributive belt
8. Bolt
9. Sealing ring of the water pump
10. Water pump
11. Asterisk of a cranked shaft
12. Bolts
13. Bottom cover of a gas-distributing belt
14. Sinkhronizatsionny label
15. Bolt
16. Pulley of a cranked shaft
17. Shock-absorber
18. Pulley and shock-absorber bolt
19. Pulley bolt

PERFORMANCE ORDER
1. Disconnect a wire of the minus plug of the accumulator.
2. Lift and fix a forward part of the car.
3. Remove a front bumper.
4. Remove both lobbies of a headlight.
5. Disconnect a rope from the lock of a cowl and remove a cross-piece.
6. Unscrew fastenings of a radiator and shift it aside, without disconnecting from it hoses.
7. Remove the radiator fan.
8. Remove an additional driving belt.
9. Remove a natyazhitel of a driving belt.
10. Establish the N1 piston in VMT, remove the top and bottom covers of a gas-distributing belt.
11. Unscrew a bolt of a pulley of a cranked shaft, previously having stopped a flywheel.
12. Weaken bolts of a natyazhitel of a gas-distributing belt, turn a natyazhitel counter-clockwise to weaken his pressure. Remove a gas-distributing belt.
13. Remove the shock-absorber of a cranked shaft together with a belt.

Check

Examine a belt on existence of pollution by greasing or oil, and also on existence of wear or damages. If necessary replace a belt.

Installation

PERFORMANCE ORDER
1. Put on a gas-distributing belt and an asterisk of a cranked shaft. Tighten an asterisk bolt. The arrow specified an adjusting ledge.
2. Combine sinkhronizatsionny labels.
3. Turn a natyazhitel clockwise to pull a belt. A belt will pull correctly if it can be overwound no more than on 90 °. Tighten bolts of a natyazhitel.
4. Establish the remained details.