Audi 100/A6

1990-1997 of release

Repair and car operation



Audi 100/A6
+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Engines
   + 3.1.1.2. Technical characteristics
   + 3.1.2. 5-cylinder engines
   - 3.1.3. 6-cylinder engines
      3.1.3.2. Gear belt
      3.1.3.3. Head of cylinders
      3.1.3.4. Valves
      3.1.3.5. Replacement of maslosjemny caps of valves
      3.1.3.6. Check of directing valves
      3.1.3.7. Fair processing of a landing facet of the saddle / valve
      3.1.3.8. Grinding in of saddles of valves
      3.1.3.9. Compression check
      3.1.3.10. Poliklinova belt
      3.1.3.11. Greasing system
      3.1.3.12. Oil pump
+ 3.2. Diesel engines
+ 3.3. Removal and partition of engines
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. Exhaust system
+ 8. Systems of start, ignition
+ 9. Transmission
+ 10. Brake system
+ 11. Suspension brackets, steering
+ 12. Body
+ 13. Electric equipment
+ 14. Good advice


ff85f19c

3.1.3.10. Poliklinova belt

Removal

PERFORMANCE ORDER
1. Remove a casing of a poliklinovy belt. For this purpose turn out 2 bolts of SW 10 and unfasten a casing from the screen of coils of ignition.
2. The engine with working volume of 2,8 l and 30 valves (193 h.p.): Unscrew the fan with the vyazkostny coupling. For this purpose as a stopper insert into one of four openings of a pulley of a poliklinovy belt a screw-driver and обоприте it on a fan arm with the vyazkostny coupling. A wrench turn on to the right (the left carving). Remove the fan.
3. Designate an arrow on a poliklinovy belt by means of a felt-tip pen or a marker the direction of its movement. The cranked shaft of the engine rotates if to look in front, to the right, that is in the direction clockwise.
4. Maple a belt weaken. For this purpose turn the tension device, as is shown in drawing, in the arrow direction a ring wrench of SW 15 and stop a suitable pin (Ф 6 mm), for example, AUDI-3204. Previously a screw-driver remove a plastic cap from a tension roller.
Prevention

At the engine in capacity of 193 h.p. a six-sided ring key of 17 mm insert under a tension roller, an arm of a tension roller turn to the right and stop.


5. Poliklinova a belt remove.

Installation

PERFORMANCE ORDER
1. Impose poliklinovy a belt at first on driving and directing rollers and only then on a tension roller.
Prevention

If the belt which was in the use is again established, it is necessary to pay attention to the direction of its movement. Belt installation in the opposite direction increases wear and can lead to its break. Therefore it is necessary poliklinovy to establish always a belt so that the put arrow showed in the direction of rotation of a shaft of the engine (if to look in front, in the direction clockwise).


2. Establish poliklinovy a belt on belt pulleys. Slightly press the tension device in the arrow direction. Pull out a plug-in pin. After that slowly turn a natyazhitel against the arrow direction, paying attention to the correct provision of a poliklinovy belt on belt pulleys.
3. Engine in capacity of 193 h.p.: The fan with the vyazkostny coupling tighten to the left the moment of 40 Nanometers.
4. Establish a casing of a poliklinovy belt. Establish a plastic cap on a tension roller.