Audi 100/A6

1990-1997 of release

Repair and car operation



Audi 100/A6
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 3.2. Diesel engines
- 3.3. Removal and partition of engines
   - 3.3.2. Technical characteristics
      3.3.2.2. Inhaling moments
   3.3.3. Repair work, possible without engine dismantle
   + 3.3.4. Major maintenance
   3.3.5. Removal and engine installation
   3.3.6. Engine partition
   + 3.3.7. Head of cylinders
   3.3.8. Pistons and rods
   + 3.3.9. Cranked shaft
   3.3.10. Intermediate shaft
   3.3.11. Block of cylinders
   3.3.12. Radical bearings and bearings of rods
   3.3.13. Piston rings
   3.3.14. The first start of the engine after a partition
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. Exhaust system
+ 8. Systems of start, ignition
+ 9. Transmission
+ 10. Brake system
+ 11. Suspension brackets, steering
+ 12. Body
+ 13. Electric equipment
+ 14. Good advice


ff85f19c

3.3.2.2. Inhaling moments

GENERAL INFORMATION

Moments of an inhaling, Nanometer

ADR engine
The bolts, fixing a natyazhitel of a driving belt of the compressor of the air conditioner
20
The bolts, fixing the generator to a head of cylinders
20
Adjusting bolt of the generator
35
Bolts and nuts of a cover of a rod:
 – cтупень 1
30
 – cтупень 2
Tighten for 90 °
The bolts, fixing covers of bearings of a camshaft
10
Nuts of a cover of a camshaft
10
Bolt of an asterisk of a camshaft
100
The bolts, fixing halves of a pulley of the pump of cooling liquid
25
Ventilating air offtake of a case of the engine
20
Casing of a forward epiploon of a cranked shaft:
 – bolts М6
10
 – bolts М8
25
Casing of a back epiploon of a cranked shaft:
 – bolts М6
10
 – bolts М8
20
Bolt of an asterisk of a cranked shaft:
 – step 1
90
 – step 2
Tighten for 90 °
Bolts of a head of cylinders:
 – step 1
60
 – step 2
Tighten for 180 °
Bolts of a leading disk:
 – step 1
60
 – step 2
Tighten for 90 °
Bolts of a final collector
25
Flywheel bolts:
 – step 1
60
 – step 2
Tighten for 180 °
The bolts, fixing a plate of the sensor of the Hall to an inlet collector
25
The bolts, fixing the Hall sensor to a head of cylinders
10
Bolts of an inlet collector
10
Flange of an intermediate shaft
25
Asterisk of an intermediate shaft
100
Bolts of covers of radical bearings:
 – step 1
65
 – step 2
Tighten for 90 °
Oil filter
25
The bolts, fixing the oil pallet
20
Lock bolt of a natyazhitel of a gas-distributing belt
25
Fixing bolt of a natyazhitel of a gas-distributing belt
20
All engines except ADR
The bolts, fixing a natyazhitel of a driving belt of the compressor of the air conditioner
20
Bolts of a pulley of the compressor
20
The bolts, fixing the compressor to a casing of the air conditioner
25
Adjusting bolt of the generator
35
The bolts, fixing the generator to a head of cylinders
20
Bolts and nuts of a cover of a rod:
 – step 1
30
 – step 2
Tighten for 90 °
The bolts, fixing covers of bearings of a camshaft
20
Nuts of a cover of a camshaft
10
Bolts of a pulley of the pump of cooling liquid
20
Ventilating air offtake of a case of the engine
20
All engines except ADR
Casing of a forward epiploon of a cranked shaft:
 – bolts М6
10
 – bolts М8
25
Casing of a back epiploon of a cranked shaft:
 – bolts М6
10
 – bolts М8
20
Bolt of an asterisk of a cranked shaft:
 – step 1
90
 – step 2
Tighten for 180 °
Bolts of a head of cylinders:
 – step 1
40
 – step 2
60
 – step 3
Tighten for 180 °
Final channel of a head of cylinders
10
Bolts of an ear of the engine intended for lifting
20
The bolts, fixing an engine support to a body
45
The bolts, fixing an engine arm to a support
40
The bolts, fixing an exhaust pipe to a collector
35
Flywheel bolts:
 – step 1
30
 – step 2
Tighten for 90 °
The bolts, fixing a plate of the sensor of the Hall to an inlet collector
25
The bolts, fixing the Hall sensor to a head of cylinders
10
Bolts of a flange of an intermediate shaft
25
Bolts of an asterisk of an intermediate shaft
80
Bolts of covers of radical bearings
65
Oil filter
25
Bolts of a cover of the oil pump
10
Bolts of the oil pump
20
Sensor of temperature of oil
10
Bolts of the pump of the hydraulic booster of a steering
20
Bolts of the oil pallet
20
Bolts of a cover of a gas-distributing belt
10
Bolts of a back cover of a gas-distributing belt
20
Natyazhitel of a gas-distributing belt:
Lock bolt
20
Fixing nut
10
Engine AAN, AAR
Bolts and nuts of a cover of a rod:
 – step 1
30
 – step 2
Tighten for 90 °
Bolts of a cover of the bearing of a camshaft
20
Bolts of a cover of a camshaft:
 – step 1
5
 – step 2
10
 – step 3
12
Bolt of an asterisk of a camshaft
65
Ventilating channel of a case of the engine
20
Bolt of an asterisk and pulley of a cranked shaft
450
The bolts, fixing pulley and the shock-absorber of a cranked shaft to an asterisk
20
Bolts of a casing of a back epiploon of a cranked shaft:
 – М6
10
 – М8
20
Oil jet of the cylinder
10
Bolts of a head of cylinders:
 – step 1
40
 – step 2
60
 – step 3
Tighten for 180 °
Bolts of support of the engine
45
The bolts, fixing an exhaust pipe to a collector
40
Bolts of a final collector
25
Flywheel bolts:
Standard flywheel:
 – step 1
30
 – step 2
Tighten for 90 °
Flywheel two-piece:
 – step 1
40
 – step 2
Tighten for 180 °
The bolts, fixing a plate of the sensor of the Hall to an inlet collector
25
The bolts, fixing the Hall sensor to a head of cylinders
10
Bolts of a cover of the radical bearing
65
Bolts of an inlet collector
20
Oil filter
25
Maslozaborny branch pipe
10
The bolts, fixing the oil pump to the block of cylinders:
 – the short
10
 – the long
20
Bolts of the oil pallet:
 – М6
10
 – М8
20
Cap of the oil pallet
40
Bolts of support of the engine
40
Bolts of covers of a gas-distributing belt
10
Bolts of a natyazhitel of a gas-distributing belt
20
Fan
20
Engines 1Z, AHU
The bolts, fixing an arm of the generator and the compressor of the air conditioner to the block of cylinders
25
The bolts, fixing the compressor to an arm
20
Generator bolt
25
The bolts, fixing the lever of an additional belt to a natyazhitel
10
The bolts, fixing a natyazhitel of an additional belt
25
Bolts and nuts of a cover of a rod:
 – step 1
30
 – step 2
Tighten for 90 °
Bolts of a cover of the bearing of a camshaft
20
Bolts of a cover of a camshaft
10
Bolts of a cover of the first bearing of a camshaft
20
Bolt of an asterisk of a camshaft
45
Bolt of a pulley of the water pump
25
The bolts, fixing the water pump to the block of cylinders:
 – step 1
20
 – step 2
Tighten for 90 °
Ventilating channel of a case of the engine
20
Bolts of a casing of a forward epiploon of a cranked shaft:
 – М6
10
 – М8
25
The bolts, fixing pulley and the shock-absorber of a cranked shaft to an asterisk
25
Bolts of a casing of a back epiploon of a cranked shaft:
 – М6
10
 – М8
20
Bolt of an asterisk of a cranked shaft:
 – step 1
90
 – step 2
Tighten for 90 °
Bolts of a head of cylinders:
 – step 1
40
 – step 2
60
 – step 3
Tighten for 90 °
Bolts of an intermediate plate of the engine
10
The bolts, fixing ears for engine lifting to a head of cylinders
20
Bolts of the top cover of the engine
5
The bolts, fixing an exhaust pipe to a turbonagnetatel
25
Flywheel bolts:
 – step 1
60
 – step 2
Tighten for 90 °
The bolts, fixing a plate of the sensor of the Hall to an inlet collector
25
The bolts, fixing the Hall sensor to a head of cylinders
10
Flange of an intermediate shaft
25
Asterisk of an intermediate shaft
45
Bolts of covers of radical bearings:
 – step 1
65
 – step 2
Tighten for 90 °
Bolts of an oil radiator
25
Oil filter
25
Bolts of a cover of the oil pump
10
Bolt of the oil pump
25
Bolts of a pulley of the pump of the power steering
25
The bolts, speeds fixing the sensor to a cranked shaft:
 – step 1
10
 – step 2
Tighten for 90 °
Bolts of a maslozaborny branch pipe
10
Bolts of the oil pallet
20
Bolts of an internal cover of a gas-distributing belt
10
Bolts of the bottom external cover of a gas-distributing belt
10
Nut of a natyazhitel
20
The bolts, fixing the top cover to the engine
5
The bolts, fixing the hydrotransformer to a leading disk
35
The bolts, fixing cover and transmission arm to the block of cylinders
45
Bolts of the vacuum pump
20
Engine ABP, AAT, AEL AAS
The bolts, fixing the generator to an arm
45
Bolts of a natyazhitel of a driving belt
20
Bolts and nuts of a cover of a rod:
 – step 1
30
 – step 2
Tighten for 90 °
The bolts, fixing the vacuum pump of brakes to a head of cylinders:
ABP, AAT, AEL
10
AAS
20
Bolts of a cover of the bearing of a camshaft
20
Bolts of a cover of a camshaft
10
The bolts, fixing covers of forward and back bearings of a camshaft
20
Bolt of an asterisk of a camshaft:
ABP, AAT, AEL:
 – step 1
30
 – step 2
Tighten for 90 °
AS:
 – bolt 8.8
85
 – bolt 10.9:
    • step 1
30
    • step 2
Tighten for 90 °
Ventilating channel of a case of the engine
20
Ventilating channel (ABP, AAT, AEL)
10
Bolt of a pulley of a cranked shaft:
ABP, AAT, AEL release to 11/94:
 – step 1
160
 – step 2
Tighten for 180 °
ABP, AAT, AEL release after 11/94:
 – step 1
220
 – step 2
Tighten for 270 °
ASS
450
Casing of a back epiploon of a cranked shaft:
 – М6
10
 – М8
20
Oil jet of the cylinder
10
Bolts of a head of cylinders:
 – step 1
40
 – step 2
60
 – step 3
Tighten for 180 °
 – step 4
Warm up the engine
 – step 5
Tighten for 90 °
 – step 6 (only ABP)
Tighten for 90 ° after 1000 km
The bolts, fixing an exhaust pipe to a collector (AAS)
40
The bolts, fixing an exhaust pipe to a turbonagnetatel (to ABP, AAT, AEL)
40
Flywheel bolts:
 – step 1
30
 – step 2
Tighten for 90 °
Bolts of a cross-piece of a forward suspension bracket:
 – step 1:
   • AAS
110
   • ABP, AAT, AEL
100
 – step 2
Tighten for 90 °
The bolts, fixing an arm of the fuel pump to the block of cylinders (AAS)
50
The bolts, fixing a cover of a driving belt of the fuel pump:
To a head of cylinders
20
To the fuel pump
10
Bolt of an asterisk transferring a drive to the fuel pump:
ABP, AAT, AEL
100
AAS
160
Bolt of an asterisk of the fuel pump
50
The bolts, fixing the fuel pump to an arm (AAS)
25
The bolts, fixing a plate of the sensor of the Hall to an inlet collector
25
The bolts, fixing the Hall sensor to a head of cylinders
10
Bolts of a cover of the radical bearing:
AAS
65
ABP, AAT, AEL:
 – step 1
30
 – step 2
Tighten for 90 °
Oil filter
Reduktsionny valve of the oil pump:
Cap without the temperature sensor
40
Cap with the temperature sensor
30
Bolts of the oil pump
20
The bolts, fixing a maslozaborny branch pipe to the pump and the block of cylinders
10
The bolts, fixing the power steering pump to an arm
20
Bolts of the oil pallet
20
Intermediate pulley of a gas-distributing belt
10
Bolts of an internal cover of a gas-distributing belt
10
Bolts of an external cover of a gas-distributing belt
20
Nut of a natyazhitel of a belt
Bolts of fastening of the cooling fan
10
Fan bolts
20